Start small plastic recycling plant precautions!
Many beginners do not pay attention to this, the hands of tens of thousands of dollars, to inquire about cheap machine was less than 20,000 yuan, began to dry. In fact, the investment budget is very important, otherwise it will cause a lot of problems later, the starting point is too low, eventually battered, defeated.
First, we must understand that a small plastic recycling plant is now very thin profits, in order to make a profit, not detours as possible. It is best to own a car, own car, so you can save some shipping. But now to buy a car, even if the old, it may have about 30,000 yuan to buy the machine, if produce 40 tons, investment in machinery to be at around 40,000 yuan. Then by the choice of a good renovation sites, factories, rows of machines, equipment lines, so down, I am afraid to be in 8-90000 yuan. Then start feeding, general inventory how they have more than ten tons of it. Finished goods inventory when many probably have about ten tons, so that should be more than ten million. Many beginners think that, with the finished product to sell right away, you can turnover, in fact, finished too little, customers do not want to pull, is willing, the price will be low for. Moreover, at the beginning, due to unskilled, assorted goods inevitably more and more types of particles must also, if you have the goods on the throw, the lowest bidder will increase the early loss. Therefore, adequate working capital, is a normal start-up granulation plant necessary.
In so doing, invest in a small plastic recycling plant to be around 200,000.
Second, the feed articles
Well, now we have everything you need, of course, feed the next. This, novices must pay attention to the equipment installed, just waiting for the material, and often eager novices production, see the material on the pull, Lee Ji Gong is good, it makes us pay more for the price. Novices often do not know how to budget, and that there are a lot of people have old customers material, some people will catch you eager to feed the psychological, kill your knife, if not kill, anyway, he can sell to existing customers. Therefore, we must see more, to find, through the Internet, ah, ah friends and other means. Some get as much information, which for the novice who is very good.
For some packaged goods, it must be carefully examined, there are some packing material on the market, the outside is not the same with the intermediate mass, novices often gullible. Secondly, some of the more complicated material, it must be careful that these materials which tend to have a lot we do not need material, a composite film. Novice can easily pull these materials do not understand the budget because of a loss. Therefore, as far as possible to pull some of the pure material, it is easier to budget for some. If possible, it is best to have some of the same granulation friends, introduce them to pull through some of the material they are made, so, to secure some. Also, you can according to their own customers to sell production quotas, such as they have expertise eat feed customers, then we can Dora some better quality raw materials. If not, we recommend that novices who just started doing some low-grade material, do not ask, if a loss occurs, thanks also less. Also, if possible, pull as far as possible from the factory directly, so eliminating the intermediate link, naturally much cheaper.
Avoid the roadside stalls up those special little pull. Because they are extremely rare material, human psychology slaughter some seriously, and their hybrid materials, poor quality. Should find those available than the larger customers. For imported materials, I am afraid that is unfit for novices. After the time is ripe to do right.
Third, the production of articles
It is easier to be a novice overlooked aspect, that just go get materials, finished products will be able to draw the pin, the production brought on to the old master is needed. In fact, the production process is simple, but also the management is very important. Grandfather invited although relatively familiar with the production process, but not necessarily best. Between them is not responsible for and in charge can give you cause no small loss. On my humble opinion, should pay attention to the following issues.
1, picking, this one is especially important for feed but miscellaneous friend. To pay attention to pick out a good clean material, categorized, according to the level of stacking, poor feeding in sometimes good material, pick out individual making material, sometimes you can sell more than a thousand dollars. Competent rolling material, never water rolling, so you can save the next one mill, power. Because there is no water, you can also Sheng Mei. Special attention should single out the inside of the other miscellaneous materials, such as vinyl chloride, the composite film and so on.
2, production, when it comes to production, first of all talk about safe and unsafe places should be equipped with protective devices. When the operation must emphasize to use feed rod, does not allow direct feeding by hand, to avoid a long time crush plastic wrap around the arm. You can try to regulate the electrical installation, electric shock protection is indispensable, the motor must install a thermal relay to avoid burn a later phase line, causing the motor burned. Shutdown at night, after the closure stove, be sure to pay attention to the board and underground around feeding clean, because the shutdown inevitable screw there are more than expected, sometimes overheat and cause a burn, flames sprang in the charging port or vent in .
To find ways to improve yields, decrease power consumption and coal consumption to. In the manual, the general contracting methods are based. Pay attention to the quality of the workers because it is contracted, the sooner the better, give you mess rolling along, just talk about production. So, when you yourself go, there must be a able to give you the supervision of the responsible person. Avoid frequent refueling in order to reduce the middle section when refueling miscellaneous materials production. Machine maintenance should also be noted that a large screw bearings, once every two days we must add the butter. When the water rolling, pay attention to the charging port dredge dredge the bottom drainage holes. Because in the case of poor drainage holes, if just the seal is damaged, water will enter the gearbox, causing gearbox wear rapidly increasing, resulting in unnecessary losses and troubles. The material must be tightened dock, thus reducing the marina material, but also to avoid the obliterated pier. For the new machine, do not bother, we must trial. The resistive material stems adjusted to the optimum state. For some miscellaneous materials, pay attention, do not have metal objects, feeding stage must be careful not to put the blade, scissors, screwdrivers and the like metal objects to avoid entering the machine jammed screw.
Fourth, the sales papers
For starters, this is a hurdle, after this hurdle, the future is bright ah!
Some of those who assisted us, this is very easy for me, but, peer is the enemy Yeah, so for most number of people, unlikely. Many colleagues will kill your knife, you sold the material, which has to take part of the benefits, and he does not give you direct contact with customers.
So how should we novices do? Obviously the Internet can help us understand the market, not being slaughtered too hard. However, the price of particles of different customers for the novice is really difficult to determine, because the new material has a standard, but back to the material, but there is no uniform standard, are generally expected to see about price, because the same is a very material, If you put a piece of material, you will find sometimes there will be very different. And many customers will catch you are a novice, eager to ship psychological characteristics, he will kill as many of your knife, it is recommended not to rush novice shipments, at least do not let the customer see it, of course, as much as possible with customer contact is certainly beneficial. This can help you understand your goods should be able to sell what price. Then, we can according to their own supply situation to decide how we walk a path of development. If our goods more complex, then it must be noted that the incoming goods relative to have the price advantage, because we have the finished product will be very complicated, everything, so can only be sold traffickers, dealers sold, the price is relatively will be lower. Otherwise, we should make their own characteristics, designed to do the same, so we will be relatively larger amount, we can sell directly to the manufacturers, the price will be relatively high, because the price is a little high, so we acquired they also have the advantage, you can get out compared to others bid higher. This will have a competitive advantage. However, many manufacturers will place an order, contract or contracts, to determine the amount of your supply, but will be more particular about the quality of some, that we have to consider that, if the contract is set up, but for goods not on, it can be No, oh.
Category
Search
